NEW Instalacion de OpenWrt en Comtrend CT-536+Por aqui tengo uno de telefonica, quien no tiene uno de estos
si no te gusto el poligon puedes probar lo mejorcito en firmwares pero la adsl se te pierde, sera como un router neutro pero tu mandaras en la maquina.
Lo mejor que lo haces via web y sin miedo al ladrillo.
Miras las imagenes, el modo facil es este:
Pon tui tarjeta de red en 192.168.1.1 asi vamos mas seguros.
Encender el router con el boton del reset pulsado hasta que apague la luz de encendido y en el navegador, supongo que da igual el que sea, pones No tienes permiso para ver enlaces.
Registrate or
Ingresa.1.1 y ya estan listo para meterle el kamikaze
No tienes permiso para ver enlaces.
Registrate or
IngresaUpdate SoftwareStep 1: Obtain an updated software image file from your ISP.
Step 2: Enter the path to the image file location in the box below or
click the "Browse" button to locate the image file.
Step 3: Click the "Update Software" button once to upload the new image
NOTE: The update process takes about 2 minutes to complete, and your DSL
Router will reboot.
Software File Name:
DSL Router Software UpgradeNew software is being programmed to the flash memory. The DSL Router will
reboot upon completion. This process will take about 2 minutes.
Ya lo tienes dentro, ahora a disfrutar si eres de los que gustan el cacharreo.
login as: root
root@192.168.1.1's password:
BusyBox v1.13.4 (2009-06-01 15:41:02 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
KAMIKAZE (bleeding edge, r16284) -------------------
* 10 oz Vodka Shake well with ice and strain
* 10 oz Triple sec mixture into 10 shot glasses.
* 10 oz lime juice Salute!
---------------------------------------------------
root@OpenWrt:~# dmesg
Linux version 2.6.27.24 (travis@devsandbox) (gcc version 4.1.2) #2 Tue Jun 2
03:57:06 PDT 2009
Detected Broadcom 0x6348 CPU revision a2
CPU frequency is 256000000 Hz
16MB of RAM installed
board_bcm963xx: CFE version: 1.0.37-5.17
console [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348GW-11
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802680a0, node_mem_map 802ae000
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
cons
ole=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 64 (order: 6, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13496k/16384k available (2070k kernel code, 2888k reserved, 334k
data, 1
28k init, 0k highmem)
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
net_namespace: 592 bytes
NET: Registered protocol family 16
registering 37 GPIOs
registering PCI controller with io_map_base unset
PCI: 0000:00:01.0 reg 10 32bit mmio: [0, 1fff]
bus: 00 index 0 io port: [8000000, 800ffff]
bus: 00 index 1 mmio: [30000000, 37ffffff]
Switched to high resolution mode on CPU 0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.301:1): initialized
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler cfq registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW-11.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
Creating 5 MTD partitions on "bcm963xx":
0x00000000-0x00010000 : "CFE"
0x00010100-0x000f0000 : "kernel"
mtd: partition "kernel" doesn't start on an erase block boundary -- force
read-o
nly
0x000f0000-0x003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=270000, len=180000
0x00270000-0x003f0000 : "rootfs_data"
0x003f0000-0x00400000 : "nvram"
0x00010000-0x003f0000 : "linux"
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <
greearb@candelatech.com>
All bugs added by David S. Miller <
davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX
(1)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: topology change detected, propagating
br-lan: port 1(eth1) entering forwarding state
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found!
b43-phy0: Broadcom 4306 WLAN found (core revision 5)
phy0: Selected rate control algorithm 'minstrel'
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
root@OpenWrt:~#
root@OpenWrt:~# df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 1536 1536 0 100% /rom
tmpfs 6812 84 6728 1% /tmp
tmpfs 512 0 512 0% /dev
mini_fo:/tmp/root 1536 1536 0 100% /tmp/root
/dev/mtdblock3 1536 208 1328 14% /jffs
mini_fo:/jffs 1536 1536 0 100% /
root@OpenWrt:~#
NOTA: Si no guarda la configuracion metele esta linea.
root@OpenWrt:~#
mtd -r erase /dev/mtd3 Unlocking /dev/mtd3 ...
Erasing /dev/mtd3 ...
Rebooting ...
NOTA2: Usa el putty para entrar por telnet.
No lo tocare mucho por que funciona a 16v y yo tengo todo a 12 y 5 pero va bien tener algo donde practicar.
Aqui teneis mas del tema,
Instalación de openwrt en CT-5361
No tienes permiso para ver enlaces.
Registrate or
IngresaLa wireless no funciona, hay que darle al linux.
Total de Usuarios: 
Visitantes: 46
Oculto(s): 0
Usuarios: 7
Usuarios en Línea:
Labor Day
